New Products Page, Quick of Japan  Helicopters.                   Contact Helicopter Hobbies for more information.

Heavy Duty Servo Arms  for the EP8v2 EX & SP ! This is a new stronger, and longer servo arm which is proven to make the EP8 fly much better.  Note: The two rear servos have been mounted on the bottom for equal linkage lengths on each side. This setup flys equal cyclic right and left stick! This has proven to be the best flying setup for Helicopter Hobbies. This special ordered servo arm works great on the Hitec metal gear servos, in stock now! Helicopter Hobbies, home of the First 500 size heli in the US!!

Stronger Skids for the EP8v2 EX ! This is a new stronger skid for the flyers using the 6 Cell Battery setups. The skids are thicker to support the weight of the 6 cell battery and bigger motors.  They will be the same price, in stock now!

EP8v2 SP and EX Fly Bar Lock Original design Flybar Lock for HH has been tested to be a good setup tool for the EP8 !  Now you can setup your EP8 using this specially designed tool to hold the flybar and get accurate pitch degree settings! In stock now!

SwashPlate Leveling and Linkage Setup Tool The new Swash Plate setup tool is great  to help the pilot setup the linkages and level the swash plate! This unit can be put under the swash without removing links, easy to use, makes setting up your heli much easier!

HeCell 3 Cell 450mah Li-Poly Radio Battery The is a good battery to run on a heli for separate radio control. This way you do not loose radio voltage if you loose the main battery. HeCell batteries has proved to be a high performance quality battery for HH.

MS Composit Carbon Fiber Tail Rotor Blades MS Composit Carbon Fiber Rotor blades have proven to give good performance on the Quick helis. Many customers have purchased these blades for the EP8v2 SP and EX. These are the CF MS Composit 80mm5/3 blades. Caution: These blades must be cut off to run them with the 420mm Main Rotor Blades!!

Viper lightweight high performance parts for the EP8v2 EX and EP8v2 SP The new EP8 landing gear are lighter than the stock gear. All of these new HH products are for the ultimate 3-D pilot who wants the lightest machine for real performance. In the right bottom photo the new lighter one piece motor mount from Japan is used on the left side, we used it for the photo only, the numbers will be some different using the new mount.

HeCell's New 14.8v 4000mah 25C pack These fresh new 25C packs are in, they are super strong packs that have high output to the end of the charge! This 14.8v 4000mah pack has been tested on the new EP10 helicopter and shows brut power running the Mega 22/30/3 motor! For the best in batteries, run HeCells!!

HeCell's new 6 Cell 22.2v 3000mah 25C pack This is the new 25C pack from HeCell which is the high performance battery for the EP8v2 EX. These packs just come in and have been tested and flown by Neil Edmonston on his EX which shows top 3-D performance!! Neil showed his EX at SEFF last weekend flying in the 25 and 30mph winds all weekend, thanks Neil !

Carbon Fiber 420mm and 470mm  Rotor Blades for the EP8v2 EX These 420mm MS Composit rotor blades have been tested on the EP8v2 EX with the stock tail boom on the heli by Neil Edmonston of Florida. Neil has put the EX through 3-D for the past weeks and states these are the best rotor blades he has flown. The craftsmanship looks very good on these blades. 470mm blades are used with the EP8 stretch kit and on the EP10.

The new 36mm Medusa 1000 for the EP8v2 EX. Over 1 Horsepower output has been measured with the new Medusa 1000 on the EX using the new 25C HeCell battery. This is a proven new performer turning the MS Composit 420mm rotor blades on Neals EX at SEFF.

Run the big Motors!!!!  More elevator servo arm clearance!!!!!   The new Viper EX frames. This is the best performance frame for the EP8v2 EX that you will find!!  It is strong and lightweight. My designer has redesigned the EX frames which give more that enough room for the elevator servo arm when running the larger motors on this frame. You can use the Hitec HS-81MG or the 85 with no problem. Helicopter Hobbies now releases the new Viper EX lightweight design for the hard core ultimate 3-D performance. Features new skids, new battery lo rails, new main frames, and the lightweight one piece motor mount. The skids saves over 6 grams, the main gear saves over 6 grams, the motor mount is the EX part that has been computer cut and lightened by approx. 12 grams.  These frames can be run on the SP.

The new EP8v2 Skids. Helicopter Hobbies now releases the new EP8v2  Skids. These skids are forgiving and are not rigid.  They are very good for beginner heli pilots with their wide stance, but best of all, they are over 5 grams lighter than the stock metal skids!

The new Lo Rails, longer and no weight added! Helicopter Hobbies now releases the new EP8v2  Lo Rails.  G10 Fiberglass  cut to give much more space to mount the battery further out front for better balance when running one 3 or 4 cell battery. Also it provides better battery mounting for the hard 3-D pilots who really have the wild thing going on!. The best part about this is there is no increased weight gain!!!

New main frames and the new Lo Rails, run the big motors now!!! Helicopter Hobbies now releases the new EP8v2 main frames and the new Lo Rails. The main frames feature G10 Fiberglass and are cut to give much more space between the motor and the elevator servo arm, bigger  motors now can be used with more space for the elevator arm. The new Lo Rails offer more frame area to mount the battery, also one 4 cell Li-poly battery can now be moved further forward for better balance when running one 4 cell. The best part about this is there is no increased weight gain!!!

QEP08-OH-7C Rigid Damper Spacers for the EP8v2 EX, not the SP. This new release from Quick of Japan is made to stiffen up the spindle shaft for better 3-D flying. The head and spindle shaft are included in the picture for explanation purposes only. .

QEP08-OF-2C  Frame Strengthening Cross Members for the SP and the EX. Quick of Japan has released their new Cross Members to go between the frames and use 3mm bolts to make the frame rigid for high motor performance applications. The cross members are 30mm long.

The New  Brushless Outrunner 16v3 Combo Quick of Japan has now released their new 16v3 and QJ 18 Combo. The combo includes a new Quick Outrunner motor with a 6mm output shaft, a 21 tooth pinion, and a 90 Amp ESC. The ESC features large gauge silicone insulated wire for high current power loads. More info will be available soon. See 16v3 options page for more infomation.

The New JP3019-10-J Brushless Outrunner Helicopter Hobbies has tested this motor with 3 cells and 4 cells and it tests to be a very strong motor on the EP8!  Comes with a motor fan, mounting screws, female connectors for the ESC, male connectors are pre-installed on the very nice silicone wire leads from the motor.  This motor is available in Motor-ESC combo deals with the SP or EX kits. Features of this 990KV motor is on the EP8v2 SP Motors Page.

The New JP3025-10-J Brushless Outrunner  Helicopter Hobbies is proud to sell this new Quick of Japan motor for the EP8v2 EX heli. This motor has tested to draw 17 amps in a hover with a 5 cell li-poly battery with a 21 tooth pinion on the motor.  Comes with a motor fan, mounting screws, female connectors for the ESC, male connectors are pre-installed on the very nice silicone wire leads from the motor.  This motor is available in Motor-ESC combo deals with the SP or EX kits. Features of this 890KV motor is on the EP8v2 EX  Motors Page.

The New Quark 65A ESC This controller is one of the newest, smoothest, most responsive ESC's on the market. The first programming you do with this ESC is actually calibrate this controller to your transmitters low and full throttle stick positions. Comes with heavy duty motor wires and female connectors for the ESC. This ESC is used with a max. number of 6 Li-poly cells. Features a cutoff switch for the ESC. It is programmed by moving the transmitter stick to the position which turns on the combination of lights on the ESC. A very good manual comes with the ESC.   Helpful hints and a wiring drawn layout is available from Helicopter Hobbies for customers. Tested, proven on the QJ8 and QJ16v2.

Quick of Japan CNC metal fan improves cooling of the outrunner motor, lightweight CNC design for best efficiency.  Fan is shown here on a Hacker A30-10L Outrunner motor.

CNC 2.0mm metal frame set with a one-piece motor main shaft mount that resists frame twisting of the most powerful motors for 3-D. These frames are CNC made by Quick of Japan and comes with the main shaft bearing and mounting bolts and the CNC center motor main shaft one-piece mount

FR4 G10 Fiberglass QJ8 Frames Part No. 4 S BLK-M.,  use the micro size tailrotor servo. The new G10 Frames for the QJ8 are a direct replacement of the stock frames. Made of good quality FR4 G10 the frames have good strength. These frames are much lighter than the stock frames. The frames come in black or blue (Part No. 4 S BL-M) color. This frame cut offers the same servo placement and size as the stock QJ8 frame.

FR4 G10 Fiberglass QJ8 Frames Part No. 3 S BL-M/R,  use the micro size or a regular size  tailrotor servo. The new G10  QJ8 Frames will mount a micro or standard size tailrotor servo.. Made of good quality FR4 G10 the frames have good strength. These frames are much lighter than the stock frames. The frames come in blue or black (Part No. 3 S BLK-M/R) color. This frame cut offers the same servo placement and size as the stock QJ8 frame.

FR4 G10 Fiberglass QJ8 Frames Part No. 2 MM BL-M/R,  use the micro size or a regular size  tailrotor servo. The new G10  QJ8 Frames will mount a micro or standard size tailrotor servo.. This frame is used with the one piece motor main brg mount unit which resists motor torque twisting for the most powerful inrunner motors. This frame does not come with the one-piece motor main shaft mount. These frames are much lighter than the stock frames. The frames come in blue or black (Part No. 2 MM BLK-M/R) color. This frame cut offers mounting the micro or a standard size tailrotor servo.

This picture was requested by Nhut Tran (Mcallen, Texas) to show our customers how to make up a series wire set to put 2 batteries in series. This wire connector wiring can be used for example to make a 6 cell setup out of 2 three cell battery packs. It could be used to make up an eight cell pack out of 2 four cell battery packs. This picture is used to help customers only. Make sure all solder joints are properly soldered and insulated. Questions? email us, we can not be responible for accidents on the makeup or construction or else of wiring.

The Optional 16v2 16v3  and QJ18 Battery, Radio Tray This is the new Battery-Radio tray for the 16v2 and the QJ18. This one piece fits directly between the main frames and is easy attached by wire ties if desired. The fiberglass offers good strength and makes for a good mounting device to get the battery out front for proper balance of the heli. This mount with be made in black and blue.

G10 Tail Rotor Plates for the QJ8 These are the new G10 Tailrotor plates for the QJ8. These come in black and blue. These plates are made from 1/16" fiberglass and offer considerable weight saving being mounted on the rear of the tailboom. Comes without the flange bearings needed for these plates. Helicopter Hobbies will stock the bearings needed for these plates.

G10 Gyro Mounting Plates for the QJ8 This is the G10 fiberglass plates to mount the gyro on the QJ8. Made to fit in the rear between the framesof the heli above the tailboom. Cut in black and blue of the 1/16" fiberglass.

G10 Battery Radio Tray This is the G10 fiberglass mounting plate designed by Mr. Henry Gardner of Bristol Tenn. which allows you to mount your radio and components plus mount the batteries in front of the frame for better balancing your heli, Thanks Henry. Cut in black or blue fiberglass, same product as above.

QEP08-OH-3C  Hiller Control Arms These new Hiller Control Arms make setup of the fly bar much easier.  The fly bar to washout arm linkages are easily aligned with this system. These also come in silver for the EP8v2 SP Heli.

EP8v2-OF-6 Rudder Tail Boom Servo Mount The new Rudder Servo mount from Quick of Japan comes with the mounting blocks and allows direct inline control of the tail rotor control lever.

Shocker 30 and EP16 & 18 Decal Set This new decal set is made from high quality vinyl material and comes in many different colors.

EP8v2 EX G10 Fiberglass Frames and Lo Rail     NEW!   EX G10 Fiberglass Frames and Battery Tray, sold separate.  One (1) frame shown in picture. FG frames are 49.74 grams lighter than stock frames,  more than the wt. of one stock frame!   For wt. comparison click on the picture.

HELICOPTER HOBBIES
PO Box 123  Pageland, SC 29728
Phone. 704.624.6473    Email: quickfighter@windstream.net
Our Hours are from 8:00 a.m. to 7:00 p.m. Eastern