Pilots with their Quick of Japan  Helicopters.


Scott Metze  says "This EX Rocks!!"  Scott has the EP8v2 EX with HH G10 frames and lo rails, Medusa 1000 motor, will get all his information later.  More of his pictures are coming soon.

Randy Swann of Hendersonville N.C. with his new EP8v2 EX  machine. The Quick of Japan J-3025-10-J Outrunner motor and the PCB-52-J ESC  50 Amp is used to power the machine.Randy uses a JR radio  with a Futaba 401 gyro on his machine.  HiTec HS-81mg servos are used with the stock servo arms. 

Rhett Bryson of Greenville S.C. with his new EP8v2 SP. Rhett runs his QJ8 with the new Quick of Japan motor combo with the 1170 KV outrunner motor and the 40 amp ESC and a 21 tooth pinion. 

Neil Edmonston of Pensacola Fla. with his EP8v2 EX with all hard 3-D equipment. Neil uses the Medusa 1000 KV motor with a 14 tooth pinion, 6 cell 2100mah HeCell batteries and 3000mah batteries have been tested on this machine. Neil has kept the heli light using the HH G10 Fiberglass main frames. More information will be posted soon about this powerful machine.

David Stewart and his son Devon from Spartanburg SC. David is using a Hitec Eclipse 7 Radio, Rx is a JR R700, 3 Hitec
HS-81 servos for ccpm control, Futaba Digital 9650 servo on tail rotor with a 401 Gyro, Inrunner Medusa 1400 motor  with
a 9 tooth pinion, CC HV45 ESC,  Sky Technology Digital BEC(Battery Eliminator Circuit), 2 three cell Thunder Power
2100mah batteries in series. David does 3-D aerobatics with his EP8v2 SP. David uses 400mm Wood Main rotor blades
and the 385mm MAH CF blades. David is also running Helicopter Hobbies G10 Fiberglass main frames and G10 Batter tray.

Henry Gardners QJ16v2, AXI 2826-10 Outrunner motor, Quark 65A ESC, Medusa 3.5 BEC, Futaba 9Z radio, 148 DP PCM RX, 401 Gyro, 4 Hitec HS-225MG servos, 2 He-Cells 4s2p Lipos in parallel(4200mah total),Base loaded antenna. Astro Flight 109 charger. Tail rotor uses a Hitec 635MG servo. Henry uses CF tail rotor blades and stock CF main blades..
Run Ryder User Name:  Henry
Heli Freak User Name:  Henry
RC Universe User Name: Ka3muf
Next Helicopter:  QJ8v2 EX or QJ6(which ever is available first)

 David Mouser, Dexter MO.  EP8v2 SP.  David uses a Hitec Eclipse 7 channel radio with PCM rec., Hitec HS-81servos  on cyclic and tail rotor servo, Futaba 401 Gyro, Hacker A30-10L motor with a 17 tooth pinion, Quark 65A ESC, Sky Technology BEC and 400mm wood blades from Japan.  This is David's first  electric heli and he has built a nice looking kit. David uses
the HeCell 4 cell Li-poly battery for power.  Setup:  Normal Mode  +9.0 degrees, 3.5 degrees, -1 degree.  Throttle Curve numbers are 0, 35, 75, 80 & 85 in normal mode.  The model hovers just above mid stick.  Thanks David!!

Chris hovered his QJ8 with no problems at all, very well built heli!

Chris Buchanan of Jefferson S.C. with his QJ8(EP8v2 SP), Futaba 9 Channel radio, Hacker A30-10L Motor, 17 tooth pinion, 
Quark 33A ESC, Medusa BEC, 4 Hitec HS-81 servos, Futaba 401 Gyro, 400mm Main Rotor Wood blades. Chris uses
one 4cell HeCell Li-poly battery to power his QJ8.

Rick Vander Kaay hovering the QJ8 Sportsman on a windy weekend at Belpre Ohio, good hovering, thanks for the picture Rick!.

Rick Vander Kaay from Charlotte N.C. JR 9303 Radio, Receiver JR R770PCM, AXI 2814-12 outrunner, 25 Tooth motor pinion, Castle Creations 35 ESC, HS-85MG servos, BEC Medusa 2.0,  Futaba 401  gyro. Hitec Digital tail rudder servo HS-5245MG Mighty Mini Digital, . Rick runs Thunderpower 3S2P 11.1V 4200 mah batteries on his QJ8 which shows good performance and over 15 minutes run time.. Thanks for the nice pictures Rick!

Neal Hayes of Spartanburg with his EP8v2 SP,  JB3019-10-J Outrunner and PCB-54-J ESC,
Hitec HS-81 servos and a Futaba 401 gyro. Neal says he runs a 3 cell 2220mah battery and flies for 8 minutes and lands. He states the heli is very stable and flies great.  

Will says his Shocker 30 hovers very good.

 Will Spears' Shocker 30, O.S. 37 motor, JR radio, Futaba 401 gyro, Quick of Japan 30 muffler.  Will runs the Quick of Japan 550mm wood main blades. Will has put together a very nice looking machine, this was his first heli, you can not tell it by looking at the well built heli.

Mike bought the QJ8, complete with the silver Rotorworks Carbon Fiber Frames with rec. and gyro mounts at the Joe Nall.

Mike Price's QJ8(EP8v2 SP), Hacker A30-8XL Outrunner, 15 tooth pinion, JR 9303, Rec JR 790 PCM scan select, 
Swash servos 3 Hitec HS-81's, Futaba 401 with a 9650 mini digital on tail rotor, Castle Creations HV45 ESC, Sky 
Technology Digital BEC,  MAH385 CF Main rotor blades. Rotorworks CF frames. 2-3cell 2100mah Thunder Power
series together to make 6cell 25.2 volts. 
Throttle curves, normal-68.5, idle 1 -73.5, idle 2-78.0,  Pitch positive 12 and negative 12.
email-WorldsTopRCPilot@aol.com
helifreak sn- MadMikey
rc universe- BadBoy_MadMikey

 Mike Price's Shocker 30  JR 9303, Rec. JR 790 PCM 
. 
Throttle curves, normal-68.5, idle 1 -73.5, idle 2-78.0,  Pitch positive 12 and negative 12.
email-WorldsTopRCPilot@aol.com
helifreak sn- MadMikey
rc universe- BadBoy_MadMikey

Tim brought his very nice painted QJ30 Pro from Va. to show it on the table at the Joe Nall, Thanks Tim.

Tim Pilkenton's QJSP30 Pro, Futaba radio, O.S. 46 motor, Futaba gyro, Ouick of Japan 30 muffler. 

Julian and Harold, Julian learned with this QJ8, picture taken at the Spartanburg Knights Heli Fun Fly April 1, 2006.

Julian Higgs' QJ8,  Futaba 7CHP,  Futaba 146 Rec.,  Futaba 3101 servos, 401 Gyro with 9650 digital
tail rotor servo, G10 Fiberglass main frames, 400mm wood main rotor blades, Hacker A30-10L motor, Quark 33A
ESC, Medusa 3.5, BEC. Julian uses a 3 cell pack with a 17 Tooth pinion and he also runs a 4 cell Li-poly Thunder
Power 2100mah with a 13 Tooth pinion for more run time.  This EP8v2 SP uses Quick 16 landing skids.  Julian
learned to hover using the 16 landing gear skids.  Julian is from Kannapolis N.C.

 

Randy Swann's QJ50, JR 8103 Radio, JR790S Rec., Futaba 9202 Servos, Futaba 401 Gyro, JR 2400 battery
pack. Randy runs  +10 degrees at full stick, 0 degrees at mid stick, and -10 degrees at low stick. Randy runs
30% Cool Power Fuel in his QF50 OS Hyper 50 motor and his Shocker 30. Randy is a member of most of the RC Groups.
   Randy's picture with the QJ18 at the Joe Nall is in the October 2006  issue on page 106 of the AMA magazine.

Robbie is a good 3-D pilot, see his inverted hovering QJ8 on page 5 photos

Robbie Woods' QJ8, JR radio and servos, Futaba 401 gyro, AXI2820-10 motor and Castle Creations HV45 ESC, Medusa 3.5 BEC.  Robbie uses the 400mm wood rotor blades.  Robbie is any excellent 3-D pilot from Denton N.C.

Dereck learned to hover and took the training skids off the helicopter on the 3rd tank of fuel the club members tell me!!!

Derek Bryans' QF50,  O.S. 50 Hyper Motor, Quick of Japan 50 muffler JR radio and servos, Futaba 401 gyro. Derek is from the Hendersonville N.C. area.

Henry Gardners QJ8(EP8v2 SP), Hacker A30-10L motor, Quark 33 ESC, Medusa 3.5 BEC, Futaba 9Z radio, 148 DP PCM RX, 401 Gyro, 4 Bluebird 380MGBB servos, 400mm Wood Main rotor blades, Slow-down counter gear(25T), HelicopterHobbies Stock G10 frames, Base loaded antenna. Astro Flight 109 charger and Tanic 4 cell Li-polys 2450mah.
Run Ryder User Name:  Henry
Heli Freak User Name:  Henry
RC Universe User Name: Ka3muf
Next Helicopter:  QJ8v2 EX or QJ6(which ever is available first)

These are Quick of Japan Pilots at the Etowah NC Fun Fly .

Etowah NC Fun Fly, this was a good FF we are all looking forward to in 2007, Good people, good food, good flying and good times!  Located in the Hendersonville NC area.

Bradley Petty with his new Shocker 30.

Bradley Petty's Shocker 30  JR 9303 Radio, Futaba 401 Gyro, O.S. 37 Motor, Quick of Japan muffler, 550mm Japan wood rotor blades, Cool Power 30% fuel.

Bradley Petty showing QJ8s of his own and Mike Price at the Skyknights Electric FF.

Bradley Petty  EP8v2 SP  JR 9303 Transmitter, Rec. JR R700,  3 Hitec HS-81 servos, Tail rotor  is a Futaba 9650 digital servo, Helicopter Hobbies G10 Fiberglass main frames, Japan long motor mount, Futaba 401 Gyro, Medusa 1400 Inrunner motor, 9 tooth pinion, Quark 65A ESC, Sky Technology BEC, Thunder Power 6cells 2100mah, 2 HeCell three cell 
2100mah batteries in series.
Quark 65A ESC, Medusa 3.5 BEC, 6 cells 14Tooth pinion, Hitec 81 Servos Mike Galang of Virginia Beach Va., Hacker A30-10XL motor, Quark 65A ESC, Sky Technology digital BEC, Hitec HS-81 servos, Futaba 401 gyro, 400mm wood blades, Mike runs HeCell Li-poly batteries, 2 three cell packs in series.
Barry Thaxton, a great helicopter pilot! Barry Thaxton with one of his QJ8's. Barry is one of the best heli pilots, with experience and knowledge.
Hacker A30-8XL Motor David Stewart        Hitec Eclipse 7 Transmitter, Rec. JR R700, Servos 3 Hitec HS-81, Tail Rotorservo is a Futaba 9650 digital servo, Helicopter Hobbies G10 Fiberglass main frames, Japan long  motor mount, Futaba 401 Gyro, Medusa 1400 Inrunner motor, 9 tooth pinion, Castle Creations HV 45  ESC, Sky Technology BEC, Thunder Power 6cells 2100mah.
Helicopter Hobbies stocks the Alum, and G10 frames Bradley Petty  EP8v2 SP  JR 9303 Transmitter, Rec. JR R700,  3 Hitec HS-81 servos, Tail rotor  is a Futaba 9650 digital servo, Helicopter Hobbies G10 Fiberglass main frames, Japan long motor mount, Futaba 401 Gyro, Medusa 1400 Inrunner motor, 9 tooth pinion, Quark 65A ESC, Sky Technology BEC, Thunder Power 6cells 2100mah, 2 HeCell three cell 
2100mah batteries in series.

Henry Gardners' 16v2

Gene Leon Guerrero of  CA. This QJ8v2 SP  is running a long version tail boom and 440mm main rotor blades.

Gene Leon Guerrero of  CA. also has a EP8v2 EX.  Motor Z power Z20 1450KV, CC HV45 ESC, Koolflight
5V UBEC, Hitec HS-81MG, Futaba 401 Gyro w/ 9650 on tail rotor servo, 18T pinion, with a 4S2P 4200 Li-poly
battery.  3000 RPM head speed, Max. 50 Amp with average 22 Amp draw.  Gene uses 28V Emolis drill batteries
sometimes which give 2700 RPM range.  Photos to come in soon.  Thanks Gene!
Randy Swann of  Hendersonville N.C. also flies a Shocker 30. JR 8103 Radio, JR790S Rec., JRDS811
digital servos, Futaba 401 gyro, JR 2400 battery pack. Randy runs Cool Power 30% fuel in his OS 37 motor
in this heli. 
James McLemore from Beaumont Texas EP8v2 EX, Futaba Radio, AXI 2820-10 Outrunner, Quark 65A ESC,
Medusa BEC, HS-81 servos, 18 tooth pinion.  James will be sending pictures soon and his sign on. Jim runs a 4 cell 
li-poly battery on the EX heli.
James McLemore from Beaumont Texas EP8v2 SP, Futaba Radio, AXI 2820-10 Outrunner, Quark 65A ESC,
Medusa BEC, HS-81 servos, 18 tooth pinion.  James will be sending pictures soon and his sign on. Jim runs a 4 cell 
li-poly battery on the SP heli.
Marvin Goins  EP8v2 SP   Hacker A30-8XL motor, Hitec 85MG servos, Futaba 401 Gyro with 9650 servo
on tail rudder. Marvin runs 5 Emoil batteries on his heli.
Mark Bankoles QJ16v2, Mark is a college student in New Mexico who flies 3-D. Mark uses the AXI2826-10
brushless outrunner, Jetti ESC, Medusa BEC, Futaba 401 Gyro, CF blades. Mark says he flies the 16v2 inverted
and states it is a smooth performer.